Does not alter factory wiring. Plugs into factory ignition coil connectors. 3ft harness length. Flying leads to hardwire AutoMeter 9117 Tach Adapter

Accomodates 5 or 6 gauge installations consisting of any AutoMeter In-Dash Tachometer Speedometer and four short sweep electric air-core gauges (Fuel Level Oil Pressure Water Temperature and Voltmeter). Color coded and pre-terminated for simpified installation.. Not intended for use with the following AutoMeter gauge types: Digital Stepper Motor Digital Display Dual Gauge Mechanical Quad Gauge or Tach/Speedo Combo.. Includes: Main Wire Harness (gauge side and vehicle side with pre-terminated multi-pin separation connectors). Lighting Ground Wire Harness 8 butt connectors 8 crimp connectors 2 green turn signal LEDs 1 amber high beam LED 1 red brake or check engine LED.

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Includes 3 aluminum mounting brackets 6 lockwashers and 6 aluminum thumb nuts.

Includes 3 aluminum mounting brackets 6 lockwashers and 6 aluminum thumb nuts.

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Includes 3 composite mounting brackets 6 lockwashers and 6 aluminum thumb nuts.

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Sensor Body Materlal - Plated steel. Thread size - 1/8" NPTF. Includes 1/4" NPT adapter bushing.. Measures 3.25" long from end of threads to tip of sensor stud and 2" in diameter.. Not compatible with fuel.

Sensor Body Materlal - Plated steel. Thread size - 1/8" NPTF. Includes 1/4" NPT adapter bushing.. Measures 3.25" long from end of threads to tip of sensor stud and 2" in diameter.. Not compatible with fuel.

Bosch LSU4.2 replacement sensor only.. M18x1.5 Male threads. 10" wire lead with connector. Free air calibration not required. Designed specifically for use with AutoMeter Wideband AFR gauges. Accurate to within 0.1 AFR

Narrowband sensor kit designed specifically for use with AutoMeter narrowband AFR gauges. M18x1.5 Male threads. 8ft. Wire harness. Stainless weld fitting and plug included

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)

Replacement 2 BAR absolute pressure sensor designed specifically for AutoMeter high precision vacuum and boost gauges.. Built in connector mates to Delphi Packard connector #12015796 (not included). 1/4" hose nipple. Mounting holes 2.5" on center. Measures: 3" Long x 1.85" Wide x 1.25" High

Replacement 3 BAR absolute pressure sensor designed specifically for AutoMeter high precision vacuum and boost gauges.. Built in connector mates to Delphi Packard connector #12015796 (not included). 1/4" hose nipple. Mounting holes 2.5" on center. Measures: 3" Long x 1.85" Wide x 1.25" High

Sensor Body Material - Brass. Thread size - 1/8" NPTF

8 ft. wire length

Sensor Body Material - Brass. Thread size - 1/8" NPTF

Sensor Body Material - Brass. Thread size - 1/8" NPTF

Sensor Body Material - Brass. Thread size - 1/8" NPTF. Includes 3/8" NPT and 1/2" NPT adapter bushings.